If you own or are planning to purchase a Bosch induction cooktop, you might encounter some errors when using it. It is essential to be aware of these errors to be armed with the right information when you encounter them.
According to Bosch service data, the most common error codes that occur in Bosch induction cooktops are E2 (35% of cases) and E6 (25% of cases). Furthermore, 70% of Bosch induction cooktop error codes are caused by faults in temperature monitoring, power supply, or the controls and electronics.
If you would like to know more about these error codes, read on to find them listed with their causes and the best corresponding solutions.
At the writing of this post, my friend has a Showgreen induction that had a similar Bosch error F4 that they fixed with the solution below.
Bosch induction cooktop error codes – Troubleshooting, causes and solutions
Here’s a table for a quick guide on how to solve Bosch induction cooktop error codes.
| Error code | Possible cause(s) | Solution |
| None | No power connection | Check the power supply and make sure the equipment is receiving the required |
| The device has not been connected as directed | Ensure the equipment is connected to the power supply following the circuit diagram in the manual. | |
| Electronics fault | If the problem persists, inform the technical after-sale team. | |
| F2 | The electronics have overheated, leading to the switching off of the corresponding hotplate. | Switch off your unit and wait for it to cool down. Then touch any symbol and the problem should be gone. |
| F4 | The unit is overheated and always switches off all the hotplates | Wait for your unit to cool down. Then touch any symbol. |
| F5 | There is hot cookware in the control panel area. This should never happen and is a sign of overheating | Remove the cookware from the control panel area. Then wait for some seconds. This will give your nit time to autocorrect itself and correct any errors. |
| F1/F6 | The hotplate has been switched off to protect the work surface due to overheating. | Wait until the hotplate is cooled down, then switch on again. |
| F8 | The hotplate was working for an extended time without interruption | Check and deactivate the automatic safety switch-off function in your cooktop. |
| E9000/ E90 10 | There is a fault in the supply voltage. It must be out of the normal operating range. | Contact your induction cooktop technician. |
| 0400 | The hob is not correctly connected | Check the power connection to your induction hob. |
General Error Codes for Induction Cooktops
Is your induction cooktop flashing weird numbers or letters at you? We’ve all seen those mysterious error codes pop up from time to time. But what do they actually mean?
Not to worry, we’ve decoded the most common induction cooktop error codes to help you troubleshoot what’s going on. Whether it’s E0, E1, E2, or more, we’ll explain what each error stands for in simple terms.
Our handy infographic below breaks down what’s causing these pesky induction error codes, and how to potentially fix the problems yourself.
Major Induction Cooktops Error Codes Explained
How do you reset an induction cooktop?
If you try pressing your induction cooktop, but notice it’s unresponsive, the best solution is to reset it. To reset your cooktop, go to the circuit breaker and cut off the power to your induction cooktop.
Keep the power off for at least 30 seconds. This process will do a hard reset on your induction cooktop. It can reset the lock function on your cooktop when you turn the power on again.
Why is my induction hob not working?
If your induction hob is not working, you first need to think about its power connection to ensure it’s working right. And also check for tripped-off circuit breakers.
The second reason why your induction hob is not working might be due to using the wrong cookware. Please make sure that the cookware you are using is induction compatible.
What does E mean on Bosch induction hob?
If E appears on your Bosch induction cooktop, it is an indication that your power button did not work. It means that your induction hob needs to be reset. To reset it, you will have to disconnect your induction hob from the power supply for 30 seconds and reconnect it. If the E error persists, call a technician for further diagnosis of the problem.
Why does my Bosch induction cooktop keep turning off?
If you see your Bosch induction cooktop turning off occasionally, you should not be worried because this is one of the safety features which comes with this equipment.
On normal occasions, this happens when the surface of your cooktop gets too hot. To prevent this from happening, make sure the diameter of your cookware is the same size as the burner of your induction cooktop. You should not use cookware that’s too small or too big for your burner.
What does H mean on an induction cooktop?
If you see an error code H on your cooktop, it indicates that there is residual heat in the cooking zone of your induction cooktop. In this case, allow the cooking zone to cool down if you find your cooking zone not to be hot, the sensor of your induction cooktop might be having some problems. In this case, consider calling a specialist to diagnose your induction cooktop further.
Why is my induction hob flashing F?
If you see your induction hob flashing F, it is indicating that the cookware you are using is not induction compatible. It also shows that there is no cookware on your cooktop. If you see this error and there is cookware on your induction cooktop, change the cookware and find the most suitable one for the cooktop.
Final Thoughts
As an owner of a Bosch induction cooktop, you can use this guide to clear the error codes on your induction cooktop. If you find any of the error code that persists after following the steps given, please contact Bosch’s technical after-sale service for further analysis of the problem.
Frequently Asked Questions (FAQs)
What do Bosch induction cooktop error codes signify?
Bosch induction cooktop error codes are displayed on the cooktop’s control panel, indicating specific issues or malfunctions detected by the appliance’s sensors.
Can I troubleshoot and fix Bosch induction cooktop error codes on my own?
Yes, but only for basic troubleshooting, such as power cycling the cooktop or checking for loose connections. However, for more complex issues or if the error persists, it is advisable to seek assistance from a certified Bosch service technician.
Can the type of cookware used affect the occurrence of error codes on Bosch induction cooktops?
Yes, using incompatible or improperly sized cookware can trigger error codes on Bosch induction cooktops. Only cookware with a ferromagnetic base, such as stainless steel or cast iron, is suitable for induction cooking.
Can I continue using the cooktop when an error code is displayed?
It is not recommended to continue using the cooktop when an error code is displayed, as it may indicate a malfunction that could affect the cooktop’s performance and safety. It is best to address the error before using the cooktop again.
How can I prevent or reduce the occurrence of error codes on my Bosch induction cooktop?
To prevent or reduce the occurrence of error codes, ensure proper cookware compatibility, center the cookware correctly on the cooking zone, and perform regular maintenance as per the manufacturer’s guidelines.
