Just like other electrical appliances, Induction cooktops are prone to connection-related problems. In this post, we will look into common Kitchenaid cooktop problems and their possible solutions.
Kitchenaid Induction Range Problems: Why is My Induction Hob not Working?
Your Kitchenaid induction cooktop may not work due to one of the following issues:
1. Improperly Connected Cables
The cables on the terminal block route electricity to the oven and the hob. However, the cables may fail to pass electricity due to connection problems. This may be the reason why your induction hob is not working. It is, therefore, essential to check whether the screws on the terminal block are properly tightened.
2. There is a Problem With Your Power Board
The circuit board manages all your unit’s functions, and a defect in the power board may be why your induction cooktop is not working. To verify this, conduct a thorough diagnosis on your power board and replace it where necessary. Seeing that this can be a technical issue, it is advisable to seek assistance from an approved electrician.
3. Your Electrical Installation is Faulty
Your induction unit could fail to work due to poor electrical installation. First, check whether your hob is correctly connected to the socket. If it is, proceed to confirm that your terminal connectors are appropriately tightened. You should also confirm whether the current passing is the recommended one. A current reading of fewer than 230 volts would mean that your electricity isn’t properly installed. Also, check how to install a Bosch induction hob.
4. You Have a Burnt or Extensively Damaged Terminal Block Unit
This could explain why your induction cooktop is not working. Another common reason would be that your earth wire is poorly connected. Make sure to tighten all screws, connect your earth wire properly, and replace the terminal block if it’s too damaged.
5. You are Using the Wrong Type of Cookware
The fact that you are using a non-ferrous saucepan or frying pan could be the reason your induction unit is not working. Aluminum-made saucepans don’t detect the cooking implementation in your unit. Always use cast iron or steel pans when using induction cooktops.
6. There is Insufficient Power in Your Induction Plate
Different induction plates(Bialetti) have different power requirements. Some hobs are powered by single plates, while others are powered by multiple plates/rings. Depending on the power requirement of your unit, insufficient power would keep your unit from working. It is, therefore, necessary to operate your unit at its optimum energy levels.
7. Your Hob Could be Misconfigured
Incorrectly configured hob would make the unit overheat or not work at all. It would therefore be necessary to familiarize yourself with your wattage range before you bring your appliance home.
Why Does My Induction Cooktop Keep Beeping?
You could have noticed that your induction cooktop is always making irritating noise. Where could this noise be coming from? What could this mean? Continue reading as we explain to you why your induction cooktop keeps on beeping.
The noise could be a warning sign that there is something wrong with your induction unit. A constant beeping sound from your hob could mean that all is not well. Conduct a thorough unit check-up to diagnose the specific problem. Check the socket connection, the circuit board, and the power supply. Ensure that all the components perform optimally. If you find a problematic component, don’t hesitate to replace it.
The sensitivity of your hob’s touch panel could be compromised. Melted sugar, water, or carbonized food tend to interfere with the touch panel, leading to your hob emitting beeping sounds. The solution to this would be to constantly clean your unit with mild detergent and a soft cleaning towel.
The quality of your cookware is substandard. It is not unlikely to hear some clicking noise from your induction unit when cooking from particular cookware and not when you use another one. This could mean that the quality of your first container is the problem. It is always safe to use thick-based cookware rather than ones with a bonded base.
The noise is a sign that your unit is perfectly okay. As awkward as it sounds, the noise from your cooktop could mean some good news. Sometimes, the circuit board generates electric impulses to ensure that the heating plates are functioning at their required temperature. The plate control process can be the reason why your cooktop is emitting a clicking sound.
Can You Repair Induction Cooktops?
Yes, you can. Although Induction cooktops bring a lot of convenience in cooking with their superior technology, they are prone to wear and tear, just like other pieces of machinery. Some of the commonly damaged parts of an induction cooktop include the Filter board, cooktop glass assembly, main control board, elements coil, terminal box, and the touch user interface control board.
The good news is that most of these damages are repairable. The best way to go about the repairs is to seek the services of a professional electrician. It is advisable to reach out to your appliance provider within your warranty specifications for after-sales Cooktop maintenance.
What are Some of the Kitchenaid Induction Cooktop Problems?
Common Kitchenaid problems revolve around the power control and user interface boards. These problems may affect all burners or even render the entire cooktop insolent. The best way to prevent such hazardous events would be to minimize the possibility of damage to the induction cooktop. To do so, it is essential to pay a keen eye to the following tips:
- Avoid sliding your cookware on your cooktop. Instead, you should lift your cookware and adapt using an induction cooktop cover.
- Make use of your kitchen shelves and avoid placing too many things on your cooktop
- Clean your cooktop after use or immediately when something spills on it.
- Avoid placing hot lids or aluminum foils on your cooktop surface
- Never use your induction cooktop as a cutting board. This behavior tends to scratch your unit and can, at times, interfere with the efficient performance of your induction cooktop.
- Ensure that the diameter of the cookware you are using fits comfortably and sits well on your induction heating zone.
Kitchenaid Induction Cooktop Manual
Kitchenaid induction cooktops come with manuals to help you keep your unit running smoothly. The service manual guides you on the best induction cooktop accessories to buy and at which stage of cooktop use. They also advise you on when to seek maintenance appointments or replace some components of your unit. The manuals also indicate some of your cooktop’s error codes: what they mean and their possible solutions.
What are the Common Kitchenaid Induction Cooktop Error Codes, and What do they Mean?
- C81, C82: Type 2. This error code indicates that the cooktop is overheating.
- F12: Type 1 means that insufficient current is passed to a burner’s electromagnetic coil.
- F21: Type 2 indicates that the frequency of the Mains power supply is out of range.
- F25: Type 2 draws attention to the possibility of the cooling fan being stuck or dead.
- F36 or F37: Type 1 is an indication of a failed burner temperature sensor
- F40: Type 1 or Type 2: This is a categorical indication of a failed power control board
- F42: Type 2:This error code may mean that your mains power supply voltage has a problem or the fuse is open
- F47: Type 2 indicates that there is a communication mishap between the user interface board and the power control board
- F56: Type 3. This error code shows that there is a configuration problem within the cooktop’s user interface board
- F58: Type 2. This is an indication that an invalid configuration has occurred in the cooktop’s power control board
- F60: Type 3. This is evidence of a failed user interface board.
- F61: Type 2. This is an indication of insufficient voltage going into the Power control board
What is a Kitchenaid Induction Cooktop Fuse?
A Kitchenaid induction cooktop fuse is a small but critical component of your unit. The fuse acts as a circuit breaker. This means that it’s the fuse that would suffer if there is an excessive current flowing from your power source to your unit. An induction cooktop’s fuse is located under the surface of the appliance. It is usually close to the coil. In essence, fuses prevent bigger damage to the induction cooktop as a result of ungoverned electric current.
Replacing a blown fuse is as simple as locating it, removing it, replacing it, and restoring the cooktop surface. There is, however, a need to contact your induction cooktop manufacturer if you find that the fuse blows frequently. Contact them and ask for advice. There could be more than meets the eye.
What is a Kitchenaid Induction Cooktop Control Lock?
A Kitchenaid induction cooktop control lock is an automatic shut-off control panel feature that shuts down the induction cooktop when not in use. This safety feature prevents the unintended use of the appliance. As a result, the chances of fires occurring in your household are limited. The feature also minimizes the risk of child-triggered hazardous events from happening. It is always important to have your control lock on at all times. This is why Kitchenaid manufacturers have provided a free toll call center to help you with your connected appliance.
As a Kitchenaid induction cooktop owner, always refer to this useful guide when handling your induction cooktop. We hope that the guide will help you tackle most of the common problems associated with the Kitchenaid brand. Don’t hesitate to contact Kitchenaid’s customer service desk if you find persistence in some of the discussed issues even after following the steps given. Enjoy!
